How to program subaru Key Fob to Change a Subaru Spare Key

If you lose your Subaru car key, contact a locksmith. Locksmiths are usually able to cut keys for you at a lower cost than the dealer.

Subaru car keys are usually either intelligent “push-to-start” fob remote keys or plain metal keys. The Fob keys have an embedded chip and must be reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your subaru keys made remotely. It can also open the trunk of your vehicle or the lift gate. The remotes utilize the keypad inside your car to connect to the computer in your vehicle.

Certain models of Subaru come with a lesser-known feature called PIN Code Access. It allows you to use a personalized number sequence to open and start your car. If you have a model newer than Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza that came with this feature, check the owner’s manual for instructions on how to utilize it.

It’s likely that the battery inside the key fob is dying. The first thing you’ll need to do is make sure that it has fresh batteries You can do this using a handheld remote tester or a basic multimeter that you can find in your home garage.

The next step is to remove the circuit board that controls the transmitter from the key fob and examine it. You’ll see two or three sets of 8-digits. Note down the first so you remember it. After that then put the key fob back together and you’ll be able to start programming it at home. This process varies according to the year and model of your car. However, it is generally simple enough to do yourself.

Key Fobs

Subaru’s latest models all feature key fobs that not just unlock doors however, they also turn on your lights, lock your gas cap, and start your vehicle. This is especially useful if you’ve found yourself at the gas station and your car won’t even start because the battery inside the key fob has failed.

It is likely that your subaru key replacement‘s key fob, whether it’s new or old and can be replaced. Remember that some of the most modern models, with their top-of-the-line technology, might require visiting a dealer. However, with a little time and effort, you’ll find a replacement key fob in place at home.

Begin by looking at the transmitter circuit board inside your key fob (instructions to open the case should be included in your owner’s manual). It should have one or two serial numbers each of which has 8 digits long. Note down the first number in the series and save it for reference in the future.

Then, get into your driver’s seat and close all doors. Turn the key ten times to start your car, and then switch off. Press the lock button on your key fob and then open the door to verify that all of your doors are functioning properly. Then shut the door and remove the key from the ignition. You should hear your vehicle chime again, indicating that the key fob has been programmed.

Ignition System

The battery for the key could be dead if your Subaru keys don’t work as they should. If you know how to reprogram a subaru key fob, you could replace the battery in your key fob yourself. A replacement battery is not expensive and easy to locate. If the key fob you have doesn’t respond to your commands, it could be a different issue. To find a spare key, it’s advisable to go to a dealer. They will make sure that the key is genuine Subaru key, which is covered under warranty, and will be programmed for your vehicle. This is much safer and easier than buying an aftermarket key from an organization via the internet.

The dealer can also cut a key for you if you provide your VIN number as well as evidence of ownership. They’ll use this information to program the new key to ensure that it will be accepted by the immobilizer. This is a much more complicated process than cutting a key by hand and the dealer will charge you more.

Once the new key has been programmed, you can replace it over to the working key. It will take only five seconds to insert the new key, so keep your working keys close at your side. When the security light stops flashing it’s time to remove the new key and test it to make sure that it’s functioning correctly.

Battery Replacement

One of the key features that make Subaru fobs so beneficial is their ability to turn on your car’s power windows and sunroof with just a press of a button. However, the battery in your Subaru fob isn’t made to last forever and will eventually need to be replaced. This quick guide from Capitol Subaru will help you to replace the battery on your own.

To start the process, you’ll have to find the small crack in the seam that separates the back and front of your key fob. Utilizing a small flathead screwdriver, you’ll be able to pop this seam wide to reveal a small compartment that houses the battery. Insert the new battery and ensure it’s facing in the correct direction. Remove the old one. Once you have assembled everything you can use the new key fob for locking in, unlocking, and even starting your vehicle.

Always have a spare set keys, particularly if the one you have is damaged or has gone missing. You can purchase a new key at your local dealership or get it cut by a locksmith. It is crucial that your key fob is working correctly as soon as you can so that you can drive safely.