How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an entry system that is keyless into. This key is similar to the remote control and is exchangeable by an Kia dealer.

Key fobs are prone to malfunction for several reasons, including an empty coin battery worn buttons or buttons, water damage, signal interference and a damaged receiver module. Here are some suggestions on how you can get your Kia Sportage replacement kia key key working again.

How to replace the remote key or smartkey

The battery in your 2016 kia optima key replacement cost‘s intelligent key will eventually have to be replaced, regardless of whether it is a remote key that starts with a push button or a regular metal key that does not contain transponder. This is especially when your car displays a message that indicates the smart or remote keys aren’t powered.

Luckily, this is a relatively simple process. To replace the battery in the key fob, remove the mechanical key from the hole in the back of the key fob. Then break the cover. Inside the key fob there will be the small screw that holds the battery in the correct position. Using a small screwdriver, remove the screw and remove the old battery. Then, insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock according to your expectations, then you’re all set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or when you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a machine for programming which is available to the locksmith in the automotive or dealer. Other keys (non transponder keys made of steel), do not need programming. If your key requires to be reprogrammed, you will need to know the key code number that is stamped on the tag of the key code and save the number in a secure place.

How to replace the battery

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not working properly. Fortunately replacing the key fob battery is a relatively simple DIY task that requires only the most basic tools.

Before starting the process be sure that your vehicle is off and that all doors are shut. Locate the small metal or plastic piece on the bottom of your key fob, and move it until a metal key pops out. The key can be put into the door’s driver handle to unlock your car.

To replace the key fob’s battery, remove the rear cover and use a plastic bar tool to release the latch that holds the black negative battery cable. Remove the old battery, and then orient the replacement battery to ensure its “+” side is facing you, and the “-” negative side is facing the fob’s electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or breaking the contacts of the metal.

After you have installed the new battery then turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia’s Key fob again to confirm that it’s working as intended.

How to replace the smart key?

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The smart key is equipped with an embedded mechanical key blade, while the standard key fob does not. Both key fobs contain batteries that will eventually require replacement. It’s a fairly simple process that will take about two minutes.

Be sure to turn off your Kia and stand on a level or well-lit surface prior to when you begin. Keep in mind that the fob is made up of tiny parts that could be thrown off if you’re not careful.

The first step is to find the small release button that is located on the lower backside of your fob. This will be either a circular or rectangular slot. Once you press this button, the mechanical blade will appear and you will be able to open the key fob.

Once the key fob is opened, take out the battery that was in it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. After you’ve finished with the battery, you should be able to lock or unlock your vehicle using your key fob – even if your engine isn’t running!

how to take apart a kia key fob to replace a mechanical key

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car simply by pressing the button. Like any other device, the Kia key fob might have issues. There are steps that can be taken to resolve these issues and ensure that our key fobs are in good working condition for the long term.

A dead or drained battery is one of the most common issues. The fob could be able to stop working altogether or work intermittently. If this is what you are experiencing, replace the battery with a new one.

If this doesn’t fix the issue you can try using a standard flathead screwdriver to wedge open the fob’s plastic casing. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every kia replacement keys fob comes with a spare mechanical key which will fit into the slot). Test the key fob to ensure it’s working properly. If the key fob isn’t working, contact an authorized locksmith or dealer to help solve the problem. Make sure they make you an emergency key that works for all trunk and door cylinders, to avoid lockouts again.