How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models has the keyless entry feature built in. This key usually resembles an remote control, and can be exchanged with a fresh one from an Kia dealer or locksmith.

Key fobs can stop working due to a variety of reasons, such as an inactive battery, worn out buttons signal interference, or water damage. Here are some helpful tips to help you get your Kia key fob that is a replacement for the sportage again.

How do you replace the remote key or smartkey?

The battery inside your kia key cutting‘s smart key will eventually require to be replaced, regardless of whether it’s a remote key, a push-to-start key or a standard metal key that doesn’t contain transponder. This is especially relevant if your vehicle displays a message telling you that the smart or remote locked keys in kia sorento aren’t powered.

This is a relatively easy procedure. To replace the battery on the key fob take the mechanical key from the hole in the back of the key fob. Then pry open the cover. A small screw will be inside the key fob that holds the battery in its place. With a small screwdriver, unscrew the screw and pull out the old battery. Install the new battery and then close the cut on the key fob.

When the key fob is equipped with an updated battery Test it by pressing the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you’re in good shape! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of metal) are not required for programming. If your key has to be reprogrammed, you must be aware of the number written on the tag that identifies the key and keep the number in a secure place.

How to replace the battery

If your Kia key fob isn’t responding to pressing the lock or unlock button on the fob, it is a good indicator that the battery needs to be replaced. A weak battery can cause other issues like the check engine light flashing on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a relatively simple DIY project that requires only a few tools.

Before you begin the process ensure that your vehicle is turned off and that all doors are closed. Find the small, metal or plastic piece that is located at the bottom of the key fob. Move it until the key is released. Then, you can insert the key into the handle of the door for the driver to unlock your car.

To replace the battery inside the key fob, remove the cover on the rear. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then place the new battery in a way that its “+” side is facing you and the “-” negative side is facing the fob’s electrical contacts. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or bending the contacts made of metal.

After you have installed the new battery and turning the key fob off and on in the ignition until the door locks up. Then, you can test your kia rio replacement key key fob to check if it is working properly again.

How to replace the smart key

You can have a standard keyfob or a Smart Key based upon the model of kia sportage smart key Sportage. The smart key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs contain batteries inside that will eventually need to be replaced. This is a simple procedure that takes just two minutes.

Make sure to shut off your kia picanto key fob programming and sit on a level, well-lit surface before you begin. Be aware that there are tiny pieces inside the fob which could fall out if you are not careful.

The first step is to find the small release button on the back of the lower part of the fob. This will be either an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob opened then you can take off the old battery and replace it. The new battery is a one called CR-2032 and can be bought online or in your local auto parts shop. After you’re done, your key fob will allow you to lock and unlock your vehicle even if it’s not running.

How do I replace the mechanical key?

The Kia Venga replacement key (https://toptohigh.com) keyfob is a wonderful convenience, allowing us to lock or unlock our car simply by pressing one button. Like any other device, it can have problems at times. Luckily, there are steps to take to fix these issues and keep our key fobs in good condition for the long run.

A low or dead battery is among the most frequent problems. This can cause your fob to stop working or work intermittently. If this is the case then replace the battery with an entirely new battery.

If this doesn’t solve the issue, use a flathead screwdriver standard to push the fob’s plastic casing open. Be sure not to damage any internal components, or scratch the plastic. Once the battery is removed then replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob and ensure that it’s working properly. If the fob isn’t working, call an expert locksmith or dealer to solve the issue. Make sure they cut you an emergency key that works for all trunk and door cylinders, to prevent lockouts in the future.