Reasons Your fiat Panda key fob replacement 500 Key Fob Won’t Work

A key fob from fiat ducato replacement key 500 is a handy way to unlock the doors and get started the car. There are a variety of reasons why the fob could stop working. This could be due to a dead coin battery or damaged receiver module, water damage problems, and interference.

This listing is for an NEW replacement fiat key fob not working Flip Key Remote – like the Ilco brand that must be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob that isn’t working. Modern key fobs have an operating range that is limited and must be within only a few inches from the vehicle to work. If you are not within your vehicle and you push the keyfob button it will not respond and display the message “Key Fob Not Detected”.

If this occurs, replace the coin-cell battery (Part Number CR2032) with a new battery of a reliable brand, such as Panasonic Duracell or Energizer. You can find them at your local hardware store, or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your fiat 124 spider key fob not working 500. The car should flash its parking lights, and the key fob will operate the lock and unlock switches.

If your key fob still doesn’t work even after replacing the battery, there may be water damage which is preventing it from connecting to the module inside your vehicle. Water damage can happen through a variety of methods, including an easy splash or submerging the key fob into saltwater at the beach. If you suspect your fob was exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this doesn’t work, you will require your fob to be replaced by an auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water from the chip’s electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the fob’s circuit board which causes it to short out and eventually end up dying. Getting the fob wet is not an ideal choice, but if you drop it into an empty cup of water, or fail to remove it from your pants pocket before running the washing machine and you don’t have a chance, don’t give in.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Then check the fob to see if it works. If the key isn’t working then it might need to be reprogrammed. This is usually handled by a dealer or professional auto locksmith.

If your key is old and is not programmed for your vehicle it is necessary to replace it completely. A professional locksmith for cars will be able to complete this process. The locksmith will need to cut the key to match the ignition in your vehicle. They’ll also need to reprogram the fob to your vehicle’s system. This is a cost-effective and quick procedure that can be completed on the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob may stop functioning is that it’s out of range. The remote usually has 30 feet of range or less and if it’s far from your vehicle, it won’t respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.

If you’ve replaced the battery in your coin (commonly called a “button” or “watch”) and your fob doesn’t function, it could have an internal circuit board problem. In the majority of cases, reprogramming your fob will fix the issue. You can find the procedure for the majority of vehicles on YouTube or in the owner’s guide.

You may have to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension, they could stop the battery from being properly seated, and this will cause your remote to malfunction.

In rare instances, the fob may be out of connection with your vehicle as a result of software or hardware problems. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations they might need to reinstall the program in your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This may happen if the keyfob is located in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons the key fob may not function include a weak connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you’ve tried everything at home to fix it (e.g. battery replacement fiat 500 key, reprogramming and using the spare key fob, you may have a faulty receiver module on your 500. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then interpreted by the vehicle.

Luckily, there is an easy method to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the battery 12 volt for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car’s computers, which could allow you to the key fob to function again. If the problem persists you should seek the advice of an expert technician. They’ll be able determine the root of your problem.