Patio Door Lock Repairs

Over time, patio doors undergo wear and tear which can lead to locks that fail. There are a few easy steps you can follow to ensure the security of your uPVC door.

These easy fixes will make your home safer no matter if you adjust the lock or clean the locking mechanism.

Clean the Lock

Patio doors are great to let the outdoors in and keeping out the elements. However they could pose risky for security when the lock isn’t functioning properly. Over time, wear and tear, hot and cold weather, dirt, and debris can cause your patio door lock to become difficult to operate. With some minor maintenance you can make sure that your patio door’s locks will always function effectively.

It is important to first clean the patio door lock as well as all moving parts. This will help to remove any coatings or dirt that might be hindering your lock from functioning properly. Start by wiping down all the moving parts of the lock for your patio door using a damp cloth. then make use of a scouring pad, or a rough damp cloth to scrub any difficult-to-access parts of the door and frame that are covered in dirt. Then wipe the lock using a dry towel to remove any remaining moisture. Let it air dry before you use it.

If you have a patio door that uses a pin tumbler latch mechanism You can lubricate the lock by applying graphite powdered to the key or by using a lubricant made of Teflon, such as WD-40 Multi-Use Product. This type of lubricant is easy to apply, and it doesn’t dissolve as time passes. If you’re unable find the right lubricant for your lock, make use of a pencil with a thicker tip. Put the pencil into the lock and jiggle it around a bit to distribute the graphite.

Tracks for sliding patio doors require regular maintenance to keep them free of dust, dirt, and debris. These tracks are particularly vulnerable to ice, snow, and other particles, which could cause them to block or become stuck. This can make it difficult for your patio door to be opened and closed.

You can clean the track rails and rollers on sliding patio doors by removing damaged or dirty weather stripping. Clean it, then replace it. The same is true for patio door rollers, which can be wiped down and sprayed with non-stick lubricant to help them move freely.

Lubricate the Moving Parts

upvc patio door repairs french doors, which are similar to sliding patio glass repair near me doors, operate by using 3 to 4 or sometimes 5-point locking mechanisms that include the handle and lock cylinder controlled by keys. These doors also need maintenance, specifically lubrication on the moving parts. This can be done with a thin oil (never WD40) and should be done once per year.

If sagging hinges aren’t the cause, the door could be misaligned and catching or hitting the strike plate hole within the frame. Take off the strike plate and employ a sharp tool to enlarge the mortise. This will permit the latch to fit properly into the hole, and prevent it from hitting the frame.

Measure the width of the cylinder with the help of a piece of wood or a book that fits into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the Lock’s Width

If your patio door latch is difficult to turn even after cleaning and lubricating, there’s a possibility that it’s not in alignment with the strike plate hole. Make sure that your door is in a balanced position, and that the hinge screws are tight. In a lot of cases, however, simply moving the strike plate upwards or downwards will solve the issue.

Most of the time, the issue occurs when the lock’s strike is too small for the latch to properly engage. In this situation, you’ll need to enlarge the hole using either a hammer or chisel, and then test the latch to ensure that it is able to engage the strike plate in a smooth manner without rubbing against or getting caught on the frame of the door jamb.

Before purchasing a new lock, you should first identify the type of mortise lock you currently have. This can be done by looking at the faceplate and observing whether it is round or square. Then, take a look at the screw holes in the existing lock and note the dimensions of each one. This information will assist you in finding an alternative that is the same width and fits perfectly into your existing hole.

In addition to identifying the current mortise lock, you’ll also need to check it for any bends or scratches that might require repair. A badly bent or damaged latch is more likely than one that’s been used a lot to break. Replace the lock if it displays signs of damage.

Once you’ve identified the type of lock replacement that you require, it’s now time to start the actual repair. Remove the handle and spindle from your patio door, and then install the new one. Begin by installing the handle inside, aligning it with the spindle, and then fixing it with the two bolts or screws which hold it. Once the handle in the interior is installed, put in the handle on the outside and screw it in the position as well. Once you’ve completed these steps then you can test the new handles to ensure that they are able to open and close with ease and that the latch locks correctly with the strike plate.

Make sure you check the Strike of the door.

The strike plate and door latch are two parts which work together to secure the door. If they are not aligned properly, the latch won’t latch the door shut correctly. Fortunately, this issue is usually easy to correct.

First, inspect the holes in the strike plate’s receiving to make sure they are free of obstructions such as dirt or plastic plugs. Loosen the keeper screws holding the strike plate in position. This allows it to move vertically but not separate it from the frame. Then, adjust the strike plate so that its holes for receiving align with the latch hooks on the door latch. After the strike plate has been adjusted, tighten the screws and test the door to determine if it shuts smoothly with the new adjustment.

Door strike plates can be difficult to access for homeowners who have sliding patio door repairs patio glass repair doors, however they are essential for locking and unlocking your door. These metal plates are usually placed on the top and bottom of the door jamb which is where they are used to support the door’s latch. The door latch slides into the strike plate, creating a seal when closed. If the strike plate is damaged, rusted, or is not installed correctly, the latch may not properly lock the door.

One common reason for an outdoor door lock to stick or not close is a misalignment between the latch and strike plate. The easiest way to check for this is with the “lipstick test.” Apply some lipstick along the edge of the deadbolt, and then put masking tape on it. The lipstick will leave the mark when you close the door. This will indicate exactly where the latch meets the strike plate. If the mark is too high or low it is possible to alter the strike plate.

Sliding patio door locks help keep your home safe from intruders, and if they’re not working properly, you need to repair the issue quickly. Follow these simple steps to repair your double glazed patio door repairs door lock and restore its functionality.