Reasons Why Your Nissan Qashqai Key Fob Won’t Work

The Qashqai has a distinctly SUV feel to it thanks to its larger dimensions. Moreover, the wheel sizes of 19 inches in Ti and ST-L models may be a bit stiff at times. Its front tyres can also lose grip on rough surfaces and its CVT may occasionally exhibit wrist-flexing torque steer.

It is usually due to the battery being dead, which can be replaced in just a few minutes. Make sure the replacement battery is of the same voltage, size and specification.

Water Damage

Water damage is among the most common reasons for a Nissan keyfob to display the “key ID is wrong” message. The rubber seals on the key fob guard the chip’s electronic circuit, but prolonged exposure to moisture could cause it to not function properly. It’s typical to observe this if your key fob has been dropped in the ocean or swimming pool. However, it could also happen when it gets wet from rain or soapy hands.

If your key fob was exposed to water over a long period of time, you may need to clean it with isopropyl, or an electronic cleaner. It could also require to be taken to an expert to repair or replace it.

If your key fob needs to be replaced, it’s a relatively simple procedure. First, ensure you have an appropriate multipack battery (CR2032 3V). Open the back and front cases using the help of a small screwdriver. You’ll need to take out the retaining clips made of metal and pull out the old battery, and then put in the new one. After reassembling your fob, put the mechanical key back in place and verify that it functions as intended. If it isn’t, you will need to take it to your local nissan qashqai key replacement dealer or an expert auto locksmith to fix the chip on the key. Fortunately, the chip is not usually damaged by water exposure and this shouldn’t be a huge expense.

Dead Coin Battery

Another common reason the reason your Nissan Qashqai key fob may not function is because the battery inside is dead. The batteries last for about three to five years, but are prone to failure over time if the fob has been frequently dropped. You can try replacing the battery with a new one but be sure it’s the same voltage and size as the original. If you install a new battery, it may cause the key to be assigned a wrong key ID. This will prevent it from being connected to your vehicle.

The most effective method of changing the battery inside the Nissan Key Cutting Qashqai Key Fob is to open it with an incredibly small screwdriver. Push in the screwdriver in tiny notch at the bottom of the fob and twist gently to separate the two halves of the key fob. Then, remove the old CR2025 button cell battery and insert an alternative one after taking note of its location in the fob.

Before putting the new battery into place check to ensure there isn’t any dirt or water damage on the terminals. If not, clean the terminals using some isopropyl ethanol. You should also make sure the pole cables are plugged in properly – they must be connected to the negative and positive poles of your battery, respectively.

Troubleshooting

If your nissan car key Qashqai’s keys fob stops working after exposure to pure rainwater or clean tap water, this could be a sign there is a problem with the internal chip. Changing the battery won’t fix this issue, and you’ll have to buy an entirely new key fob. If the key fob stopped working after you dropped it, it’s likely that the chip inside was damaged. If you clean the chip with isopropyl ethanol and a paper towel and then replace it with the key fob, it is possible to generally get it working.

Key ID Incorrect is a common error that can be seen on the dashboard of your car. This means that the vehicle is unable to recognize the key fob and not allow it to start the engine. This problem could be caused in numerous ways, including water damage, problems that are undetectable in the key fob circuitry or RFID interference.

The key fob will cease to function in the event that the batteries with 12 volts are not working or provide enough electric current. This will affect your Nissan Qashqai’s keyless system central locking, as well as the ability to start the engine using the key fob. Check the batteries inside the key fob if it is in a position to lock or unlock your door manually. Try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob is not been submerged in salt water and is unable to come back to life after a quick rinse with clean water. You might also try cleaning your electronic chip using isopropyl Alcohol or an electronic cleaner. If none of these works then you might need to replace the key fob.

If your nissan qashqai replacement key Intelligent Key still does not function, there may be a problem with the connection between it and the vehicle. To reconnect it, begin by turning the key in the ignition but without starting the car. Continue this process until the hazard lights flash twice. After that, turn the car off and remove the keys.

Then, you need to then open the fob compartment in your vehicle. This is usually located in the door jamb, on the handle on the driver’s side or underneath an armrest. Find the small “program” button and press it. You will hear a chime once the process is complete.

It’s time to put your Intelligent Key to the test. Click all the buttons on the key while you are at a distance away from the car. If the lights flash or the horn sounds, then the key is connected to the Nissan. You can also test it near the Nissan.