Replacing uPVC Window Handles

It is simple to change the handles on upvc windows. The most important thing is to ensure that the replacement handle fits the spindle carved out in the window mechanism.

If you follow the steps below, any cockspur handle will fit on most windows. The height of the step of the handle is key.

What to Find

Over time, upvc door handle handles on many windows in the UK may begin to show signs of wear and wear and tear. The handle on the window may become loose or difficult to operate when this happens. Anyone who is familiar using a basic hand tool is able to complete this task.

The first step is to ensure that the handle is securely attached to the frame of the window in its open position. The next step is to locate the screws or pins that secure the handle. They are usually on the inside of the handle. They can be removed using the screwdriver and pliers.

Once the handle has become loose and sagging, it can be removed from its hinges by gently pulling it off. The next step is to find a replacement handle that is the same design and size. This can be done on the internet or at an area DIY store, and the process should only take around five minutes using an screwdriver.

When replacing the handle of a upvc door handles replacement handle It is crucial to consider the step height. This is the distance from the base of the handle to the point at which it rests on the window frame. This is a standard measurement, and you should verify the height of the step before purchasing an replacement handle.

Depending on the type of handle you are using There are various sizes that are available. Inline handles for uPVC windows typically have lug centres of 31mm There are also cockspur handle types that have 43mm centres. Tilt-and-turn handles are commonly found on uPVC Windows. They feature a unique design that allows the window to be slid down to let in air and then rotated to fully open the window.

The most common breakage in uPVC handles is that they crack inside instead of breaking off from the base section. This can make them hard to open and is why it is crucial to ensure that any replacement handle you buy has the same length of spindle as your existing one.

Remove the old Handle

Incorrectly fitted or damaged window handles may cause your double-glazed windows to open or close in a way that isn’t correct and may result in them getting stuck. This can be caused by various reasons, including general wear and tear on the metal handle or corrosion. In these cases, it is important to seek replacement upvc window handles as soon as you can to prevent further damage and loss of functionality.

One of the first things that you should do when replacing window handles made of upvc is to remove the old handle from the window. To do this, start by taking off the screw that is covered when the handle is in the closed position. This should reveal another screw that once removed, you can begin to remove the handle itself. It is a good idea to use an electric screwdriver for this since it will make the task easier and quicker.

It is also important to note that the screws on the handle may be hidden behind plastic caps, so it is recommended to take an Stanley knife to the screw covers and take them off. After removing the handle, you’ll have to examine the square cutout on the base to ensure that the new handle for the window lock is compatible. It is important to measure the length of the spindle on the handle you used to replace it with and compare it to the size of the window mechanism spindle cutout.

The different types of window handles made from upvc include: Espag handles, which are equipped with a central screw and can turn left or right; Cranked handles with two screws, and are typically found on tilt and turn windows made of upvc; and Spade handles, that have an arm with a flat surface and can be placed on either side of the window. Once you have a suitable replacement, it’s simply a case of screwing the handle in place and ensuring that the spindle is correctly inserted into the lock mechanism. After that the handle should be secured to the window frame and the replacement upvc window handles should be secure.

Take a measurement of the Spindle

If you need to replace a upvc handle that has collapsed, it’s likely the spindle holding it in place is damaged or loose. In some instances you can tighten the spindle with pins or screws. In some instances, it may be necessary to replace the handle. There are several different types of handles made of upvc. They include espagnolette handles inline or cockspur handles. They also have tilt and turn handles. Each handle type is installed and replaced in a different fashion.

It is crucial to measure the handle before purchasing an alternative. This will ensure that the new handle is the correct size and will fit correctly into the window. All handles are sized in accordance with industry standards, making it easy to identify the correct size.

To determine the size of your handle, first, take it out of the window by turning it back to the open position. You should be able to see the size of the pin or screw that secures the handle. Make use of a ruler or tape measure to determine the length the spindle is. Once you know the length of your spindle it is possible to purchase a replacement that is exactly the same size.

When purchasing a replacement window handles for upvc handle, it is crucial to consider the step height of the upvc window handle replacement window handle. The step height is the distance from the bottom of the handle to where it rests on the frame. This is usually around 21mm or 9mm in aluminium and uPVC. Dropping something into the gap will allow you to determine how far the handle extends before it reaches an obstruction.

Cockspur handles often have different backset heights, based on the style of window they’re installed in. Inline Espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles however have different backset heights according to the style of the window they’re in. This is because they have a spur which extends from the handle and locks onto a cockspur wedge striking plate.

Install the new handle

After you have chosen the new handle, align it carefully with the holes for screws on the door. Then, secure it with the screws supplied. If you’re also replacing the latch lever, it can be installed in a similar way to the main door handle. After that, attach the door trim in order to conceal the mounting screws and finish the job.

Tip: To remove a metal head from a wooden wedge place the handle on the floor, so that its wide end is on the floor. Then, use an hammer and tap the thin end. Be careful not damage the handle or spindle.